Audiovox PRO9776C Manuale di Installazione

128-8787b1 of 321Model PRO9776CInstallation ManualVehicle Security Systemwith Remote StartRev B: New Format Add Timing PASD & Light Blue + DBI Loc

128-8787b10 of 32106 White w/ Black Trace Wire: (+) Siren OutputThis is the positive siren feed wire. Route this wire through a grommet in the firewal

128-8787b11 of 32119 White Wire: Parking Light Flasher OutputThis wire is the normally open contact of the on board parking light flash relay. Connect

128-8787b12 of 3212when the system is armed, the siren will emit three chirps. When the zone clears, the siren will emit 1 chirpto confirm full arming

128-8787b13 of 3213pin switch previously installed. This wire must be routed through a grommet in the firewall and connected tothe hood pin switch. If

128-8787b14 of 32142 Green: (+) Lock or (-) UnlockThe Green wire provides a (+) Positive Pulse when locking and a (-) Negative Pulse when unlocking.3

128-8787b15 of 32153 Wire Positive Switched Door Locks:In this application, the Red wire of the door lock harness provides a + 12 volt pulse during t

128-8787b16 of 3216WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS Part #1122585The auxiliary 4 pin connector provides low current outputs to control variou

128-8787b17 of 32171 Black: 250mA Output (-)The black wire switches on when the remote start is activated and will stay on as programmed in theremote

128-8787b18 of 3218and fluids warm. The operator has the option to have the unit start every 2 or 4 hours for a maximum of 48hours. Factory preset is

128-8787b19 of 32193) DBI TACH SETTINGSelecting this setting in the option menu indicates that you have a DBI module and have determined that atach si

128-8787b2 of 322Before You BeginPROFESSIONAL INSTALLATION ISSTRONGLY RECOMMENDEDRoll down window to avoid locking the keys in the vehicle duringinsta

128-8787b20 of 3220TESTING YOUR INSTALLATION:WARNING!! The following procedure must be performed after the installation of any Remote Start Device. It

128-8787b21 of 3221To Exit Remote Start Override Mode:1. With the system disarmed, Press and Hold the PBLED on.2. Turn the ignition switch on, off, on

128-8787b22 of 3222CAUTION! REMEMBER TO RECONNECT THE BROWN/BLACK NEUTRAL SAFETY WIRETEMPORARILY DISCONNECTED IN STEP 3MECHANICAL NEUTRAL SAFETY SWIT

128-8787b23 of 3223METHOD 1To connect to the key in sensor as shown in method 1:1. Locate the control wire that connects the drivers door pin switch t

128-8787b24 of 3224METHOD 2To connect to the key in sensor circuit as shown for method 2:1. Locate the control wire that connects the drivers door pin

128-8787b25 of 3225DOME DELAY LEARN FEATURE:This unit has the ability to learn the dome light delay time, up to 60 seconds. If the vehicle has delayin

128-8787b26 of 3226COMPLETING THE INSTALLATION:After you have confirmed the operation of the Remote Start unit and tested all the safety features of t

128-8787b27 of 3227INSTALLATION NOTES

128-8787b28 of 3228The transmitters are pre-programmed from the factory, If you find you need to program new or additionaltransmitters follow the inst

128-8787b29 of 3229SELECTABLE FEATURESThe selectable features of this unit can be set manually as explained on the previous page, or with the RF featu

128-8787b3 of 32318 Pin Main Wiring Harness #1123305123456789101112131415161718123Purple Door Trigger Input (+) Black/White Horn Output (-) 300mAGree

128-8787b30 of 3230PROGRAMMING BANK 3 (REMOTE START ):You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you've made

128-8787b31 of 3231RF Programmable Features Bank 3 Is Remote Start Selectable Features:Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6

128-8787b32 of 3232For technical support go to www.pursuitcarsecurity.com or call 1 800 225 6074.© 2013 Audiovox Electronics Corp., Hauppauge, N.Y. 11

128-8787b4 of 3246 Pin Power / Start Harness #1123742123456Purple Accessory (+)Blue Ignition 1 (+)Red Battery 2 - 12V (+)Red/White Battery 1 - 12V (+)

128-8787b5 of 325This Remote Start/Alarm System is designed to be used with Automatic Transmission- Fuel InjectionGas or Diesel Vehicles Only!INSTALLA

128-8787b6 of 326IMPORTANT!DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESSINTO THE CONTROL MODULE UNTIL ALL CONNECT

128-8787b7 of 327SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.YELLOW START WIRE DETAIL6 GREEN Wire: Ignition 2 OutputConnect this wire to the ig

128-8787b8 of 328WIRING CONNECTIONS: 18 Pin Accessory Input/Output Harness PART # 11233051 Black w/ White Trace Wire : 300 mA Horn OutputThe black w/

128-8787b9 of 3294. Cut (#1) wire (as shown), and connect the ignition switch side of the cut wire to terminal #87a of therelay. Connect the other sid